ODROID-C Boot-Up U-BOOT Log

A first boot of an ODROID-C.

Currently there is no Framebuffer console available, so you can only check out the logs with the usual ODROID USB-Serial adaptor.

See:

QA5:A;SVN:B72;POC:17F;STS:0;BOOT:0;INIT:10;BOOT:1;INIT:0;READ:0;CHECK:0;PASS:1;
-----------------------------------------------------------------------
* Welcome to Hardkernel's ODROID-C... (Built at 19:33:00 Dec  8 2014) *
-----------------------------------------------------------------------
CPU : AMLogic S805
MEM : 1024MB (DDR3@792MHz)
BID : HKC13C0001
S/N : HKC1CC037EB39545
0x0000009f
check SD_boot_type:0x1	 card_type:0x1
Loading U-boot...success.


U-boot-00000-ge7d4447-dirty(odroidc@e7d4447d) (Jan 20 2015 - 16:59:08)

DRAM:  1 GiB
relocation Offset is: 2ff1c000
MMC:   SDCARD: 0, eMMC: 1
IR init is done!
vpu clk_level = 3
set vpu clk: 182150000Hz, readback: 182150000Hz(0x701)
mode = 6  vic = 4
set HDMI vic: 4
mode is: 6
viu chan = 1
config HPLL
config HPLL done
reconfig packet setting done
MMC read: dev # 0, block # 33984, count 12288 ... 12288 blocks read: OK
There is no valid bmp file at the given address
============================================================
Vendor: Man 275048 Snr 7cf8d79d Rev: 3.0 Prod: SD16G
            Type: Removable Hard Disk
            Capacity: 14840.0 MB = 14.4 GB (30392320 x 512)
------------------------------------------------------------
Partition     Start Sector     Num Sectors     Type
    1		      3072	    263168	 6
    2		    266240	  30126080	83
============================================================
Net:   Meson_Ethernet
init suspend firmware done. (ret:0)
Hit Enter key to stop autoboot -- :  1  0 
exit abortboot: 0
reading boot.ini

2292 bytes read
Loading boot.ini from mmc0:1 (vfat)
Executing the script...
setenv m "720p"         	# 720p 1280x720
setenv vout_mode "hdmi"
setenv m_bpp "32"
setenv vpu "1"
setenv hdmioutput "1"
setenv condev "console=ttyS0,115200n8 console=tty0"   # on both
setenv bootargs "root=UUID=e139ce78-9841-40fe-8823-96a304a09859 rootwait ro ${condev} no_console_suspend vdaccfg=0xa000 logo=osd1,loaded,0x7900000,720p,full dmfc=3 cvbsmode=576cvbs hdmimode=${m} m_bpp=${m_bpp} vout=${vout_mode} ${disableuhs}"
fatload mmc 0:1 0x21000000 uImage
reading uImage

5438560 bytes read
fatload mmc 0:1 0x22000000 uInitrd
reading uInitrd

1993378 bytes read
fatload mmc 0:1 0x21800000 meson8b_odroidc.dtb
reading meson8b_odroidc.dtb

18305 bytes read
fdt addr 21800000
if test "${vpu}" = "0"; then fdt rm /mesonstream; fdt rm /vdec; fdt rm /ppmgr; fi
if test "${hdmioutput}" = "0"; then fdt rm /mesonfb; fi
bootm 0x21000000 0x22000000 0x21800000"
## Booting kernel from Legacy Image at 21000000 ...
   Image Name:   Linux-3.10.69
   Image Type:   ARM Linux Kernel Image (lzo compressed)
   Data Size:    5438496 Bytes = 5.2 MiB
   Load Address: 00208000
   Entry Point:  00208000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 22000000 ...
   Image Name:   uInitrd
   Image Type:   ARM Linux RAMDisk Image (uncompressed)
   Data Size:    1993314 Bytes = 1.9 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 21800000
   Booting using the fdt blob at 0x21800000
   Uncompressing Kernel Image ... OK
uboot time: 5395941 us.
Using machid 0xf81 from environment
From device tree /memory/ node aml_reserved_end property, for relocate ramdisk and fdt, relocate_addr: 0x51ef001
   Loading Ramdisk to 05008000, end 051eea62 ... OK
   Loading Device Tree to 05000000, end 05007780 ... OK

Starting kernel ...

[    0.000000@0] Booting Linux on physical CPU 0x200
[    0.000000@0] Initializing cgroup subsys cpu
[    0.000000@0] Initializing cgroup subsys cpuacct
[    0.000000@0] Linux version 3.10.69 (root@odroid-wheezy) (gcc version 4.7.2 (Debian 4.7.2-5) ) #3 SMP PREEMPT Fri Feb 27 15:16:22 CET 2015
[    0.000000@0] CPU: ARMv7 Processor [410fc051] revision 1 (ARMv7), cr=10c5387d
[    0.000000@0] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000@0] Machine: ODROIDC, model: AMLOGIC
[    0.000000@0] physical memory start address is 0x200000
[    0.000000@0] reserved_end is d9fffff 
[    0.000000@0]  
[    0.000000@0] Total memory is 1022 MiB
[    0.000000@0] Reserved low memory from 0x06000000 to 0x0d9fffff, size: 122 MiB 
[    0.000000@0] 	mesonfb0(low)   	: 0x06100000 - 0x07900000 ( 24 MiB)
[    0.000000@0] 	mesonfb1(low)   	: 0x07900000 - 0x07a00000 (  1 MiB)
[    0.000000@0] 	mesonstream0(low)   	: 0x07a00000 - 0x09a00000 ( 32 MiB)
[    0.000000@0] 	vdec0(low)   	: 0x09a00000 - 0x0da00000 ( 64 MiB)
[    0.000000@0] 	ppmgr0(high)   	: 0x3f000000 - 0x40000000 ( 16 MiB)
[    0.000000@0] cma: CMA: reserved 8 MiB at 3e800000
[    0.000000@0] Memory policy: ECC disabled, Data cache writealloc
[    0.000000@0] Meson chip version = RevA (1B:A - 0:B72)
[    0.000000@0] PERCPU: Embedded 8 pages/cpu @c149a000 s8960 r8192 d15616 u32768
[    0.000000@0] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 221200
[    0.000000@0] Kernel command line: root=UUID=e139ce78-9841-40fe-8823-96a304a09859 rootwait ro console=ttyS0,115200n8 console=tty0 no_console_suspend vdaccfg=0xa000 logo=osd1,loaded,0x7900000,720p,full dmfc=3 cvbsmode=576cvbs hdmimode=720p m_bpp=32 vout=hdmi
[    0.000000@0] cvbs trimming line = 0xa000
[    0.000000@0] cvbs trimming.1.v5: 0xa0, 0x0
[    0.000000@0] osd1:1
[    0.000000@0] loaded:268435459
[    0.000000@0] logo has been loaded
[    0.000000@0] 720p:10
[    0.000000@0] full:2
[    0.000000@0] kernel get cvbsmode form uboot is 576cvbs
[    0.000000@0] kernel get hdmimode form uboot is 720p
[    0.000000@0] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000@0] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000@0] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000@0] allocated 2060288 bytes of page_cgroup
[    0.000000@0] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000@0] Memory: 64MB 16MB 790MB = 870MB total
[    0.000000@0] Memory: 856656k/856656k available, 34224k reserved, 243712K highmem
[    0.000000@0] Virtual kernel memory layout:
[    0.000000@0]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000@0]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000@0]     vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
[    0.000000@0]     lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)
[    0.000000@0]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000@0]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000@0]       .text : 0xc0008000 - 0xc08fd90c   (9175 kB)
[    0.000000@0]       .init : 0xc08fe000 - 0xc0935300   ( 221 kB)
[    0.000000@0]       .data : 0xc0936000 - 0xc09ad8a0   ( 479 kB)
[    0.000000@0]        .bss : 0xc09ad8a0 - 0xc0cacbb4   (3069 kB)
[    0.000000@0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000@0] Preemptible hierarchical RCU implementation.
[    0.000000@0] NR_IRQS:256
[    0.000000@0] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 4294967ms
[    0.000000@0] Global timer: MESON TIMER-F (c0951080) initialized
[    0.000000@0] Switching to timer-based delay loop
[    0.000000@0] Console: colour dummy device 80x30
[    0.000000@0] console [tty0] enabled
[    0.000000@0] console [ttyS0] enabled
[    0.332626@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 2.00 BogoMIPS (lpj=10000)
[    0.342875@0] pid_max: default: 32768 minimum: 301
[    0.347845@0] Security Framework initialized
[    0.351936@0] SELinux:  Initializing.
[    0.355582@0] AppArmor: AppArmor disabled by boot time parameter
[    0.361606@0] Mount-cache hash table entries: 512
[    0.370405@0] Initializing cgroup subsys memory
[    0.370712@0] Initializing cgroup subsys devices
[    0.375261@0] Initializing cgroup subsys freezer
[    0.379847@0] Initializing cgroup subsys perf_event
[    0.384903@0] CPU: Testing write buffer coherency: ok
[    0.390259@0] CPU0: thread -1, cpu 0, socket 2, mpidr 80000200
[    0.395596@0] Setting up static identity map for 0xc064a940 - 0xc064a998
[    0.402353@0] L310 cache controller enabled
[    0.406342@0] l2x0: 8 ways, 2048 sets, CACHE_ID 0x4100a0c9,  Cache size: 524288 B
[    0.413833@0]       AUX_CTRL 0x7ec60001, PERFETCH_CTRL 0x75000007, POWER_CTRL  0x00000000
[    0.421937@0]       TAG_LATENCY 0x00000111, DATA_LATENCY 0x00000222
[    0.500320@1] CPU1: Booted secondary processor
[    0.500339@1] CPU1: thread -1, cpu 1, socket 2, mpidr 80000201
[    0.520320@2] CPU2: Booted secondary processor
[    0.520337@2] CPU2: thread -1, cpu 2, socket 2, mpidr 80000202
[    0.540307@3] CPU3: Booted secondary processor
[    0.540325@3] CPU3: thread -1, cpu 3, socket 2, mpidr 80000203
[    0.540419@0] Brought up 4 CPUs
[    0.568611@0] SMP: Total of 4 processors activated (8.00 BogoMIPS).
[    0.574838@0] CPU: All CPU(s) started in SVC mode.
[    0.580389@0] devtmpfs: initialized
[    0.589651@0] clkrate [ xtal 	] : 24000000
[    0.589695@0] clkrate [ pll_sys 	] : 1200000000
[    0.592653@0] clkrate [ pll_fixed 	] : 2550000000
[    0.597305@0] clkrate [ pll_vid 	] : 732000000
[    0.601734@0] clkrate [ pll_ddr 	] : 0
[    0.605445@0] clkrate [ a9_clk 	] : 1200000000
[    0.609861@0] clkrate [ clk81 	] : 159375000
[    0.614581@0] pinctrl core: initialized pinctrl subsystem
[    0.619730@0] regulator-dummy: no parameters
[    0.624241@0] NET: Registered protocol family 16
[    0.632421@0] DMA: preallocated 4096 KiB pool for atomic coherent allocations
[    0.636530@0] VPU driver version: v02
[    0.639042@0] load vpu_clk in dts: 182150000Hz(3)
[    0.643770@0] vpu_probe OK
[    0.648639@0] amlogic_gpio gpio: Probed amlogic GPIO driver
[    0.652338@0] register lm device lm-root
[    0.655883@0] register lm device lm1
[    0.659431@0] register lm device lm0
[    0.663034@0] hw-breakpoint: found 2 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.671095@0] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.677152@0] Init pinux probe!
[    0.680853@0] pinmux-m8b pinmux: Probed amlogic pinctrl driver
[    0.686003@0] tv_init_module
[    0.688835@0] major number 254 for disp
[    0.692656@0] vout_register_server
[    0.696015@0] register tv module server ok
[    0.734269@0] bio: create slab  at 0
[    0.735000@0] SCSI subsystem initialized
[    0.736915@0] usbcore: registered new interface driver usbfs
[    0.742428@0] usbcore: registered new interface driver hub
[    0.747908@0] usbcore: registered new device driver usb
[    0.753117@0] Linux video capture interface: v2.00
[    0.758223@0] request vpu clk holdings: vencp 106250000Hz
[    0.763158@0] TV mode 720p selected.
[    0.766689@0] already display in uboot
[    0.773770@0] Advanced Linux Sound Architecture Driver Initialized.
[    0.777103@0] Bluetooth: Core ver 2.16
[    0.780441@0] NET: Registered protocol family 31
[    0.784958@0] Bluetooth: HCI device and connection manager initialized
[    0.791483@0] Bluetooth: HCI socket layer initialized
[    0.796479@0] Bluetooth: L2CAP socket layer initialized
[    0.801705@0] Bluetooth: SCO socket layer initialized
[    0.806916@0] cfg80211: Calling CRDA to update world regulatory domain
[    0.814510@0] Switching to clocksource Timer-E
[    0.826725@0] NET: Registered protocol family 2
[    0.827453@0] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[    0.832955@0] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.839520@0] TCP: Hash tables configured (established 8192 bind 8192)
[    0.845958@0] TCP: reno registered
[    0.849307@0] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.855360@0] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.862085@0] NET: Registered protocol family 1
[    0.866537@0] Unpacking initramfs...
[    0.979411@0] Freeing initrd memory: 1944K (c4e08000 - c4fee000)
[    0.980420@0] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 3 counters available
[    0.988790@0] audit: initializing netlink socket (disabled)
[    0.993609@0] type=2000 audit(0.900:1): initialized
[    0.999244@0] bounce pool size: 64 pages
[    1.007538@0] VFS: Disk quotas dquot_6.5.2
[    1.007852@0] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.014610@0] msgmni has been set to 1200
[    1.018842@0] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[    1.024578@0] io scheduler noop registered
[    1.028659@0] io scheduler deadline registered
[    1.033180@0] io scheduler cfq registered (default)
[    1.092911@0] [drm] Initialized drm 1.1.0 20060810
[    1.093123@0] gpu cooling register okay with err=0
[    1.099538@0] Mali: Mali device driver loaded
[    1.101383@0] UMP: UMP device driver 0000 loaded
[    1.109101@0] loop: module loaded
[    1.109745@0] tun: Universal TUN/TAP device driver, 1.6
[    1.114249@0] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    1.120768@0] PPP generic driver version 2.4.2
[    1.125350@0] usbcore: registered new interface driver usb-storage
[    1.131267@0] usbcore: registered new interface driver usbserial
[    1.137145@0] usbcore: registered new interface driver usbserial_generic
[    1.143845@0] usbserial: USB Serial support registered for generic
[    1.149962@0] ERROR::usb_gadget_probe_driver:1377: usb_gadget_register_driver ENODEV
[    1.149962@0] 
[    1.157983@1] 00ffffffffffff004c2d1f043332594d3212010380331d782aee91a3544c9926
[    1.158012@1] 0f50542308008180814081009500b3000101010101013b3d00a0808021403020
[    1.158041@1] 3500fe1f1100001a000000fd00383c1e5110000a202020202020000000fc0053
[    1.158070@1] 796e634d61737465720a2020000000ff00483958514330323033300a202000bb
[    1.158071@1] 
[    1.189961@0] mousedev: PS/2 mouse device common for all mice
[    1.195663@0] i2c /dev entries driver
[    1.199131@0] IR NEC protocol handler initialized
[    1.203694@0] IR RC5(x) protocol handler initialized
[    1.208663@0] IR RC6 protocol handler initialized
[    1.213305@0] IR JVC protocol handler initialized
[    1.218002@0] IR Sony protocol handler initialized
[    1.222743@0] IR RC5 (streamzap) protocol handler initialized
[    1.228481@0] IR SANYO protocol handler initialized
[    1.233307@0] IR MCE Keyboard/mouse protocol handler initialized
[    1.239556@0] device-mapper: uevent: version 1.0.3
[    1.244343@0] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
[    1.252778@0] Bluetooth: HCI UART driver ver 2.2
[    1.257215@0] Bluetooth: HCI H4 protocol initialized
[    1.262167@0] Bluetooth: HCI BCSP protocol initialized
[    1.267251@0] Bluetooth: HCILL protocol initialized
[    1.272120@0] Bluetooth: HCIATH3K protocol initialized
[    1.277214@0] Bluetooth: HCI Three-wire UART (H5) protocol initialized
[    1.284288@0] ledtrig-cpu: registered to indicate activity on CPUs
[    1.289947@0] hidraw: raw HID events driver (C) Jiri Kosina
[    1.295636@0] usbcore: registered new interface driver usbhid
[    1.301134@0] usbhid: USB HID core driver
[    1.305329@0] efuse===========================================
[    1.311068@0] efuse: device efuse created
[    1.314919@0] efuse--------------------------------------------
[    1.320785@0] vout_init_module
[    1.323840@0] start init vout module 
[    1.327548@0] create  vout attribute ok 
[    1.331585@0] ge2d_init
[    1.333928@0] ge2d_dev major:244
[    1.337366@0] ge2d start monitor
[    1.340625@0] osd_init
[    1.340637@1] ge2d workqueue monitor start
[    1.347040@0] osd_probe, vinfo:c068b290
[    1.351138@0] Frame buffer memory assigned at phy:0x06100000, vir:0xf1000000, size=24576K
[    1.358980@0] osd_probe, mydef_var:c0981ca8, vinfo:c068b290
[    1.364491@0] init fbdev bpp is :32
[    1.368054@0] ---------------clear framebuffer0 memory  
[    1.413700@0] Console: switching to colour frame buffer device 240x67
[    1.437386@0] Frame buffer memory assigned at phy:0x07900000, vir:0xf0600000, size=1024K
[    1.445344@0] osd_probe, mydef_var:c0981ca8, vinfo:c068b290
[    1.450875@0] don't find to display_size_default from mesonfb-dts
[    1.456927@0] init fbdev bpp is :24
[    1.472981@0] osd probe ok  
[    1.506837@0] amlvideo-000: V4L2 device registered as video10
[    1.507307@0] ionvideo-000: V4L2 device registered as video13
[    1.512802@0] Video Technology Magazine Ion Video Capture Board ver 1.0 successfully loaded.
[    1.521286@0] aml_wdt_driver_init,301
[    1.524815@0] ** disable watchdog
[    1.528511@0] set uart_ao pinmux use pinctrl subsystem
[    1.533207@0] P_AO_RTI_PIN_MUX_REG:1801
[    1.537035@0] start uart_ao_ttyS0:(irq = 122)
[    1.541379@0] register uart_ao ok
[    1.544890@0] set uart_b pinmux use pinctrl subsystem
[    1.549683@0] P_AO_RTI_PIN_MUX_REG:1801
[    1.553484@0] start uart_b_ttyS2:(irq = 107)
[    1.557736@0] register uart_b ok
[    1.560992@0] dwc_otg: version 3.10a 12-MAY-2014
[    1.565540@0] dwc_otg_driver_probe NOT match
[    1.609796@0] usb1: type: 1, speed: 0, config: 0, dma: 0, id: 1, phy: fe108820, ctrl: fe080000
[    1.612936@0] USB (1) use clock source: XTAL input
[    1.638896@0] Core Release: 3.10a
[    1.638992@0] Setting default values for core params
[    1.641596@0] curmode: 1, host_only: 1
[    1.665484@0] Using Buffer DMA mode
[    1.665582@0] OTG VER PARAM: 1, OTG VER FLAG: 1
[    1.667927@0] Working on port type = HOST
[    1.672133@0] dwc_otg lm1: DWC OTG Controller
[    1.676269@0] dwc_otg lm1: new USB bus registered, assigned bus number 1
[    1.682940@0] dwc_otg lm1: irq 63, io mem 0x00000000
[    1.687846@0] -------hcd->flags.d32 = 0
[    1.692572@0] Init: Port Power? op_state=1
[    1.697198@0] Init1: Power Port (0)
[    1.702436@0] hub 1-0:1.0: USB hub found
[    1.707049@0] hub 1-0:1.0: 1 port detected
[    1.711943@0] usb0: type: 0, speed: 0, config: 0, dma: 0, id: 0, phy: fe108800, ctrl: fe040000
[    1.719676@0] USB (0) use clock source: XTAL input
[    1.745570@0] Core Release: 3.10a
[    1.750290@0] Setting default values for core params
[    1.755020@0] curmode: 1, host_only: 0
[    1.819877@0] Using Buffer DMA mode
[    1.824506@0] OTG VER PARAM: 1, OTG VER FLAG: 1
[    1.829161@0] Working on port type = OTG
[    1.833765@0] Current port type: SLAVE
[    1.838589@0] dwc_otg lm0: DWC OTG Controller
[    1.843215@0] dwc_otg lm0: new USB bus registered, assigned bus number 2
[    1.848901@0] dwc_otg lm0: irq 62, io mem 0x00000000
[    1.854302@0] hub 2-0:1.0: USB hub found
[    1.858981@0] hub 2-0:1.0: 1 port detected
[    1.863792@0] Dedicated Tx FIFOs mode
[    1.868837@0] using timer detect id change, eea60c00
[    1.873677@0] ethernet_driver probe!
[    1.878397@0] ethernetinit(dbg[c0986a3c]=1)
[    1.883094@0] ethernet base addr is fe0c0000
[    1.887834@0] write mac add to:eea85508: 00 1e 06 c3 95 45 |....E|
[    1.907747@1] Indeed it is in host mode hprt0 = 00021501
[    1.908233@0] libphy: AMLMAC MII Bus: probed
[    1.908240@0] eth0: PHY ID 001cc916 at 0 IRQ -1 (0:00) active
[    1.908244@0] eth0: PHY ID 001cc916 at 1 IRQ -1 (0:01) active
[    1.908417@0] amvideocap_init_module
[    1.908557@0] Amlogic A/V streaming port init
[    1.909986@0] init vdec memsource 161480704->228589567
[    1.910077@0] [tsync_pcr_init]init success. 
[    1.910120@0] regist mpeg12 codec profile
[    1.910161@0] regist mpeg4 codec profile
[    1.910163@0] amvdec_vc1 module init
[    1.910203@0] regist vc1 codec profile
[    1.910205@0] amvdec_h264 module init
[    1.910278@0] regist h264 codec profile
[    1.910280@0] amvdec_h265 module init
[    1.910321@0] regist hevc codec profile
[    1.910361@0] regist mjpeg codec profile
[    1.910363@0] amvdec_real module init
[    1.910403@0] regist real codec profile
[    1.910405@0] amvdec_avs module init
[    1.910566@0] regist avc codec profile
[    1.910568@0] jpegenc module init
[    1.910758@0] alloc_keep_buffer keep_y_addr ee600000
[    1.910829@0] alloc_keep_buffer keep_u_addr eec00000
[    1.910858@0] alloc_keep_buffer keep_v_addr eeb80000
[    1.910877@0] yaddr=ee600000,u_addr=eec00000,v_addr=eeb80000
[    1.911192@0] create_ge2d_work_queue video task ok 
[    1.911436@0] SARADC Driver init.
[    1.911555@0] __saradc_probe__
[    2.057766@0] saradc calibration: ref_val = 509
[    2.061554@0] saradc calibration: ref_nominal = 512
[    2.065344@0] saradc calibration: coef = 4072
[    2.069894@0] ir irblaster probe
[    2.073849@0] Remote Driver
[    2.077661@0] Remote platform_data g_remote_base=fe600580
[    2.081443@0] set drvdata completed
[    2.085156@0] device_create_file completed 
[    2.089423@0] input: aml_keypad as /devices/platform/meson-remote/input/input0
[    2.096415@0] input_register_device completed 
[    2.100685@0] [0x0] = 0x1dd0190
[    2.104475@0] [0x4] = 0xf800ca
[    2.108275@0] [0x8] = 0x82006e
[    2.111937@0] [0xc] = 0x3c0030
[    2.115492@0] [0x10] = 0x30fa0013
[    2.119054@0] [0x18] = 0x6f19000
[    2.122544@0] [0x1c] = 0x9f40
[    2.125995@0] [0x20] = 0x0
[    2.129439@0] [0x24] = 0x0
[    2.132780@0] [0x28] = 0x0
[    2.136068@0] set_remote_mode[65]
[    2.139403@0] remote config major:240
[    2.142892@0] physical address:0x2ed16000
[    2.146260@0] ==touch_ts_init==
[    2.149651@0] ==ft5x0x_ts_init==
[    2.152922@0] ==goodix_ts_init==
[    2.156203@0] i2c-core: driver [gslx680_compatible] using legacy suspend method
[    2.161628@0] i2c-core: driver [gslx680_compatible] using legacy resume method
[    2.168828@0] !!!ntp_ts: ret = 0. 
[    2.172155@0] VTL ct36x TouchScreen driver, <george.chen@vtl.com.cn>.
[    2.178633@0] i2c-core: driver [ct36x] using legacy suspend method
[    2.184712@0] i2c-core: driver [ct36x] using legacy resume method
[    2.190809@2] VTL ct36x TouchScreen driver End.
[    2.195251@2] ==gsl_ts_init==
[    2.198606@2] ret=0
[    2.201989@2] i2c-core: driver [mir3da] using legacy suspend method
[    2.206508@2] i2c-core: driver [mir3da] using legacy resume method
[    2.207685@1] usb 1-1: new high-speed USB device number 2 using dwc_otg
[    2.207962@3] Indeed it is in host mode hprt0 = 00001101
[    2.224572@2] i2c-core: driver [lis3dh_acc] using legacy suspend method
[    2.231119@2] i2c-core: driver [lis3dh_acc] using legacy resume method
[    2.237669@2] i2c-core: driver [bma222] using legacy suspend method
[    2.243827@2] i2c-core: driver [bma222] using legacy resume method
[    2.250049@2] i2c-core: driver [dmard06] using legacy suspend method
[    2.256296@2] i2c-core: driver [dmard06] using legacy resume method
[    2.262596@2] lsm303d driver: init
[    2.266082@2] i2c-core: driver [dmard10] using legacy suspend method
[    2.272246@2] i2c-core: driver [dmard10] using legacy resume method
[    2.278511@2] stk8313_init
[    2.282041@2] ======stk831x init ok======
[    2.285576@2] stk831x_init
[    2.289139@2] mxc622x accelerometer driver: init
[    2.292748@2] i2c-core: driver [mxc622x] using legacy suspend method
[    2.298744@2] i2c-core: driver [mxc622x] using legacy resume method
[    2.304960@2] mxc6255xc accelerometer driver: init
[    2.309765@2] i2c-core: driver [mxc6255xc] using legacy suspend method
[    2.316215@2] i2c-core: driver [mxc6255xc] using legacy resume method
[    2.322719@2] cm3217 v.1.0.0.1
[    2.326475@2] i2c-core: driver [elan_epl6814] using legacy suspend method
[    2.332428@2] i2c-core: driver [elan_epl6814] using legacy resume method
[    2.339124@2] i2c-core: driver [LTR501] using legacy suspend method
[    2.345309@2] i2c-core: driver [LTR501] using legacy resume method
[    2.351607@2] mmc driver version: 1.07, 2014-06-30: eMMC add hw reset function
[    2.359654@2] host->base fe108e00
[    2.363628@2] pdata->caps 78107
[    2.367466@2] pdata->caps2 0
[    2.371307@2] get property:                     port, value:0x00000004
[    2.376052@2] get property:                ocr_avail, value:0x00200080
[    2.382564@2] get property:                    f_min, value:0x000493e0
[    2.389061@2] get property:                    f_max, value:0x05f5e100
[    2.395536@2] get property:             max_req_size, value:0x00020000
[    2.399849@3] hub 1-1:1.0: USB hub found
[    2.400186@3] hub 1-1:1.0: 4 ports detected
[    2.410103@2] get property:                   irq_in, value:0x00000003
[    2.416576@2] get property:                  irq_out, value:0x00000005
[    2.423092@2] get property:                  gpio_cd, str:CARD_6
[    2.429064@2] get property:                  pinname, str:sd
[    2.434673@2] get property:                card_type, value:0x00000005
[    2.441183@2] get property:                gpio_dat3, str:CARD_4
[    2.447143@2] get property:               gpio_volsw, str:GPIOAO_3
[    2.453488@2] aml_sd_voltage_switch[1309] : Switched to voltage -> 3.30 V
[    2.517694@0] sd: mmc_rescan_try_freq: trying to init card at 400000 Hz
[    2.549717@1] aml_sd_voltage_switch[1309] : Switched to voltage -> 1.80 V
[    2.577659@2] [aml_sdhc_probe] aml_sdhc_probe() success!
[    2.582387@2] host->base fe108c20
[    2.586578@2] pdata->caps 80000507
[    2.590738@2] pdata->caps2 1
[    2.594867@2] get property:                     port, value:0x00000002
[    2.599897@2] get property:                ocr_avail, value:0x00200000
[    2.606375@2] get property:                    f_min, value:0x000493e0
[    2.611653@1] sd: new ultra high speed SDR50 SDHC card at address 0007, clock 94444444, 4-bit-bus-width
[    2.612062@1] mmcblk0: sd:0007 SD16G 14.4 GiB 
[    2.613247@1]  mmcblk0: p1 p2
[    2.630787@2] get property:                    f_max, value:0x02faf080
[    2.636075@2] get property:                  f_max_w, value:0x02faf080
[    2.642586@2] get property:             max_req_size, value:0x00020000
[    2.649083@2] get property:                  pinname, str:emmc
[    2.654865@2] get property:                card_type, value:0x00000001
[    2.661378@2] get property:                gpio_dat3, str:BOOT_3
[    2.667334@2] [is_emmc_exist] host->storage_flag=0, POR_BOOT_VALUE=1
[    2.707687@1] emmc: mmc_rescan_try_freq: trying to init card at 400000 Hz
[    2.712918@1] aml_emmc_hw_reset 1379
[    2.767655@2] [aml_sdio_probe] aml_sdio_probe() success!
[    2.771911@2] [dsp]DSP start addr 0xc5e00000
[    2.776106@2] [dsp]register dsp to char divece(257)
[    2.781258@2] aml_rtc rtc.1: rtc core: registered aml_rtc as rtc0
[    2.787455@2] amlogic rfkill init
[    2.792030@2] aml_hw_crypto initialization.
[    2.797240@2] enter rt5616_modinit
[    2.801582@2] dummy_codec_platform_probe
[    2.806161@2] i2s get no clk src setting in dts, use the default mpll 0
[    2.811717@2] test codec dummy_codec
[    2.815945@2] using external codec, index = 1
[    2.820194@2] using external dummy codec
[    2.824470@2] enter spdif_dit_probe 
[    2.828665@2] aml_spdif_unmute 
[    2.832918@2] codec_name = dummy_codec.0
[    2.837511@2] spk_event delay_time = 130
[    2.841730@2] aml_snd_m8 aml_m8_sound_card.5:  dummy_codec  aml-i2s-dai.0 mapping ok
[    2.849481@2] aml-i2s 0:playback preallocate_dma_buffer: area=f04fc000, addr=3ed00000, size=524288
[    2.857584@2] aml-i2s 1:capture preallocate_dma_buffer: area=f057e000, addr=3ec40000, size=65536
[    2.865990@2] aml_snd_m8 aml_m8_sound_card.5:  dit-hifi  aml-spdif-dai.0 mapping ok
[    2.874818@2] -----ext_codec=1---
[    2.879232@2] aml_snd_m8: faild to get mute_gpio!
[    2.883605@2] =aml_m8_pinmux_init==,aml_m8_pinmux_init done,---0
[    2.888783@2] GACT probability NOT on
[    2.893171@2] Mirror/redirect action on
[    2.898222@2] NET: Registered protocol family 10
[    2.903412@2] mip6: Mobile IPv6
[    2.907873@2] sit: IPv6 over IPv4 tunneling driver
[    2.913344@2] NET: Registered protocol family 17
[    2.917932@2] NET: Registered protocol family 15
[    2.922510@2] Bridge firewalling registered
[    2.927126@2] Bluetooth: RFCOMM TTY layer initialized
[    2.931692@2] Bluetooth: RFCOMM socket layer initialized
[    2.936300@2] Bluetooth: RFCOMM ver 1.11
[    2.940767@2] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[    2.945651@2] Bluetooth: BNEP filters: protocol multicast
[    2.951047@2] Bluetooth: BNEP socket layer initialized
[    2.956129@2] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    2.962214@2] Bluetooth: HIDP socket layer initialized
[    2.967323@2] NET: Registered protocol family 35
[    2.972429@2] VFP support v0.3: implementor 41 architecture 2 part 30 variant 5 rev 1
[    2.979721@2] Registering SWP/SWPB emulation handler
[    2.984617@2] enter meson_pm_init
[    2.989427@2] enter meson_pm_probe!
[    2.993860@2] meson_pm_probe done !
[    2.998872@2] registered taskstats version 1
[    3.003428@2] regulator-dummy: disabling
[    3.008159@2] Mali DRM initialize, driver name: mali_drm, version 2.1
[    3.013817@2] [drm] Initialized mali_drm 2.1.1 20140306 on minor 0
[    3.019692@2] Mali DRM initialize, driver name: mali_drm, version 2.1
[    3.026336@2] [drm] Initialized mali_drm 2.1.1 20140306 on minor 1
[    3.032439@2] aml_rtc rtc.1: setting system clock to 1970-01-01 00:00:00 UTC (0)
[    3.039607@2] ### dt-test ### No testcase data in device tree; not running tests
[    3.047032@2] meson_cpufreq_probe:SYSPLL request to be fixed
[    3.052581@2] meson_cpufreq: no voltage_control prop
[    3.057488@2] voltage_control = 0
[    3.063024@2] <> GTP driver installing...
[    3.066936@2] buf[0]=f,buf[1]=b1,err=4
[    3.070682@2] adc=392,TS_C=15,flag=1
[    3.074340@2] efuse_flag=a
[    3.077947@2] amlogic_thermal_probe, this chip is trimmed, use thermal
[    3.082570@2] amlogic-thermal aml_thermal: amlogic thermal probe start
[    3.089077@2] #thermal-cells=7
[    3.092687@2] pdata->temp_trip_count=4
[    3.096301@2] temperature=70 on trip point=0
[    3.100070@2] fixing high_freq=1488001 to 1488000 at trip point 0,level=3
[    3.107544@2] fixing low_freq=1488001 to 1488000 at trip point 0,level=3
[    3.114252@2] gpu[0].gpu_high_freq=511,tmp_level[0].gpu_high_freq=511
[    3.119898@2] cpu[0] core num==3
[    3.123583@2] gpu[0] core num==2
[    3.127208@2] temperature=80 on trip point=1
[    3.130834@2] fixing high_freq=1200001 to 1200000 at trip point 1,level=6
[    3.138066@2] fixing low_freq=1200001 to 1200000 at trip point 1,level=6
[    3.144758@2] gpu[1].gpu_high_freq=435,tmp_level[1].gpu_high_freq=435
[    3.150378@2] cpu[1] core num==2
[    3.154115@2] gpu[1] core num==2
[    3.157831@2] temperature=90 on trip point=2
[    3.161560@2] fixing high_freq=800001 to 696000 at trip point 2,level=11
[    3.168522@2] fixing low_freq=800001 to 696000 at trip point 2,level=11
[    3.175055@2] gpu[2].gpu_high_freq=328,tmp_level[2].gpu_high_freq=328
[    3.180683@2] cpu[2] core num==1
[    3.184293@2] gpu[2] core num==1
[    3.187831@2] temperature=110 on trip point=3
[    3.191408@2] fixing high_freq=-1 to -22 at trip point 3,level=-1
[    3.198392@2] fixing low_freq=-1 to -22 at trip point 3,level=-1
[    3.204350@2] gpu[3].gpu_high_freq=-1,tmp_level[3].gpu_high_freq=-1
[    3.209690@2] cpu[3] core num==-1
[    3.213258@2] gpu[3] core num==-1
[    3.216788@2] idle interval=1000
[    3.220306@2] pdata->name:aml_thermal
[    3.224093@2] tmp_trip[0].cpu_core_upper=1
[    3.227677@2] tmp_trip[1].cpu_core_upper=2
[    3.231249@2] tmp_trip[2].cpu_core_upper=3
[    3.235319@2] tmp_trip[3].cpu_core_upper=-1
[    3.239488@2] aml_thermal bind thermal-cpucore-0 okay !
[    3.244699@2] aml_thermal bind thermal-cpufreq-0 okay !
[    3.249872@2] pdata->tmp_trip[0].gpu_lower_level=1
[    3.254618@2] pdata->tmp_trip[0].gpu_upper_level=1
[    3.259405@2] pdata->tmp_trip[1].gpu_lower_level=2
[    3.264142@2] pdata->tmp_trip[1].gpu_upper_level=2
[    3.268930@2] pdata->tmp_trip[2].gpu_lower_level=4
[    3.273667@2] pdata->tmp_trip[2].gpu_upper_level=4
[    3.278453@2] pdata->tmp_trip[3].gpu_lower_level=-1
[    3.283279@2] pdata->tmp_trip[3].gpu_upper_level=-1
[    3.288152@2] aml_thermal bind thermal-gpufreq-0 okay !
[    3.293450@2] amlogic: Kernel Thermal management registered
[    3.298881@2] amlogic-thermal aml_thermal: amlogic thermal probe done
[    3.305569@2] input: cec_input as /devices/virtual/input/input1
[    3.311392@2] ALSA device list:
[    3.314619@2]   #0: AML-M8AUDIO
[    3.318121@2] Freeing unused kernel memory: 220K (c08fe000 - c0935000)
[    3.371406@1] udevd[107]: starting version 175
[    3.864707@3] force enable DISCARD here for ext4 fs
[    3.880363@3] checked enable EXT4 DISCARD here
[    3.883747@3] EXT4-fs (mmcblk0p2): mounting with "discard" option, but the device does not support discard
[    3.892173@3] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[    4.667947@3] udevd[316]: starting version 175
[    5.369384@1] Driver for 1-wire Dallas network protocol.
[    5.484941@1] aml_audio_i2s_mute_flag: flag=0
[    5.489290@1] aml_spdif_unmute 
[    5.594574@1] amlvideo open[    5.594604@0] ionvideo open
[    5.594769@0] ionvideo_stop_generating!!!!
[    5.594784@0] ionvideo release
amlvideo close[    6.434921@1] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[    6.718731@1] emmc: mmc_rescan_try_freq: trying to init card at 300000 Hz
[    6.757720@2] aml_emmc_hw_reset 1379
[    8.368734@3] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[    9.515226@0] aml_audio_i2s_mute_flag: flag=0
[    9.519967@0] aml_spdif_unmute 
[    9.559203@2] aml_audio_i2s_mute_flag: flag=0
[    9.563931@2] aml_spdif_unmute 
[   10.646708@0] aml_audio_i2s_mute_flag: flag=0
[   10.649192@0] aml_spdif_unmute 
[   10.686961@2] aml_audio_i2s_mute_flag: flag=0
[   10.689381@2] aml_spdif_unmute 
[   13.638474@3] netdev_open
[   13.638562@3] Ethernet reset
[   13.638653@3] NET MDA descpter start addr=edc00000
[   13.723559@3] phy_interface = 0
[   13.723665@3] aml_phy_init:  trying to attach to 0:01
[   13.726349@3] am_rtl811f called phy reset

[   13.747778@3] --1--write mac add to:eea85508: 00 1e 06 c3 95 45 |....E|
[   13.749018@3] --2--write mac add to:eea85508: 00 1e 06 c3 95 45 |....E|
[   13.755685@3] write mac add to:eea85508: 00 1e 06 c3 95 45 |....E|
[   13.761943@3] Current DMA mode=0, set mode=621c100
[   13.776727@3] ether leave promiscuous mode
[   13.776832@3] ether leave all muticast mode
[   13.779884@3] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[   13.877546@1] tvmode set to 720p
[   13.877546@1] 
[   13.877591@1] don't set the same mode as current.
[   13.956703@1] tvmode set to 720p
[   13.956703@1] 
[   13.956746@1] don't set the same mode as current.
[   14.034450@2] create_disp_get_ump_secure_id******0
[   14.034976@2] create_disp_get_ump_secure_id******1
[   16.747757@3] [adjust link] -> eth: full-duplex
[   16.747791@3] [adjust link] -> eth: phy_speed <> priv_speed)
[   16.752284@3] [adjust link] -> eth: switching to RGMII 100
[   16.757748@3] [adjust link -> eth: am_adjust_link state change (new_state=true)
[   16.765014@3] libphy: 0:01 - Link is Up - 100/Full
[   16.769847@3] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[   26.471828@2] EXT4-fs (mmcblk0p2): re-mounted. Opts: data=ordered
[   31.070577@2] ----aml_hw_iec958_init,runtime->rate=44100--
[   31.070620@2] audio_set_958_clk, freq=5,
[   31.074344@2] ----aml_hw_iec958_init,runtime->rate=44100,sample_rate=5--
[   31.081244@2] iec958 mode PCM16
[   31.084120@2] IEC958 16bit
[   31.098535@2] ----aml_hw_iec958_init,runtime->rate=44100--
[   31.098576@2] ----aml_hw_iec958_init,runtime->rate=44100,sample_rate=5--
[   31.105064@2] iec958 mode PCM16
[   31.108364@2] IEC958 16bit
[   32.737650@2] alsa capture long time no data, quit xrun!
[   33.757642@2] alsa capture long time no data, quit xrun!
[   34.777649@2] alsa capture long time no data, quit xrun!
[   35.797645@2] alsa capture long time no data, quit xrun!

 

Leave a Reply

Your email address will not be published. Required fields are marked *

Protected with IP Blacklist CloudIP Blacklist Cloud