Stefanius Hybrid-Image + serial console + danand-3.4.91 kernel

Bootlog of a Cubieboard A20 using the Hybrid Sd-Card Image of http://www.stefanius.de/

The Kernel used is based on patwood’s 3.4.79+ linux-sunxi kernel, but updated to the current 3.4.91 linux-kernel version by dan-and.

Sourcecode and repository at: https://github.com/dan-and/linux-sunxi
Binaries at http://dl.danand.de/cubieboard/


 

U-Boot SPL 2014.01-rc1-09159-ge1695e9-dirty (Jan 11 2014 – 15:05:35)
Board: Cubietruck
DRAM: 1024 MiB
CPU: 960000000Hz, AXI/AHB/APB: 3/2/2
spl: not an uImage at 1600

U-Boot 2014.01-rc1-09159-ge1695e9-dirty (Jan 11 2014 – 15:05:35) Allwinner Technology

CPU:   Allwinner A20 (SUN7I)
Board: Cubietruck
I2C:   ready
DRAM:  1 GiB
WARNING: Caches not enabled
MMC:   SUNXI SD/MMC: 0
*** Warning – bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   mii0
Warning: failed to set MAC address

Hit any key to stop autoboot:  1 0
reading uEnv.cb2
274 bytes read in 3 ms (88.9 KiB/s)
Loaded environment from uEnv.cb2
reading boot.scr
** Unable to read file boot.scr **
Failed to mount ext2 filesystem...
** Unrecognized filesystem type **
Failed to mount ext2 filesystem...
** Unrecognized filesystem type **
Failed to mount ext2 filesystem...
** Unrecognized filesystem type **
reading script-cb2.bin
46096 bytes read in 6 ms (7.3 MiB/s)
reading /uImage.3.4.79-sun7i+
5036864 bytes read in 232 ms (20.7 MiB/s)
## Booting kernel from Legacy Image at 48000000 ...
Image Name:   Linux-3.4.91-sun7i+
Created:      2014-05-28  11:08:00 UTC
Image Type:   ARM Linux Kernel Image (uncompressed)
Data Size:    5036800 Bytes = 4.8 MiB
Load Address: 40008000
Entry Point:  40008000
Verifying Checksum ... OK
Loading Kernel Image ... OK

Starting kernel ...

<6>Booting Linux on physical CPU 0
<6>Initializing cgroup subsys cpuset
<6>Initializing cgroup subsys cpu
<5>Linux version 3.4.91-sun7i+ (daniel@danand.de) (gcc version 4.8.2 (Ubuntu/Linaro 4.8.2-16ubuntu4) ) #1 SMP PREEMPT Wed May 28 13:07:28 CEST 2014
CPU: ARMv7 Processor [410fc074] revision 4 (ARMv7), cr=10c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: sun7i
<6>Memory Reserved:
<6>    SYS  : 0x43000000 - 0x4300ffff  (  64 kB)
<6>    LCD  : 0x50000000 - 0x51ffffff  (  32 MB)
<6>cma: CMA: reserved 192 MiB at 43c00000
Memory policy: ECC disabled, Data cache writealloc
<6>sunxi: Allwinner A20 (AW1651/sun7i) detected.
<7>On node 0 totalpages: 262144
<7>free_area_init_node: node 0, pgdat c096bc80, node_mem_map d2000000
<7>  DMA zone: 512 pages used for memmap
<7>  DMA zone: 0 pages reserved
<7>  DMA zone: 65024 pages, LIFO batch:15
<7>  Normal zone: 1008 pages used for memmap
<7>  Normal zone: 128016 pages, LIFO batch:31
<7>  HighMem zone: 528 pages used for memmap
<7>  HighMem zone: 67056 pages, LIFO batch:15
<6>PERCPU: Embedded 7 pages/cpu @d2808000 s8064 r8192 d12416 u32768
<7>pcpu-alloc: s8064 r8192 d12416 u32768 alloc=8*4096<c>
<7>pcpu-alloc: <c>[0] <c>0 <c>[0] <c>1 <c>
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 260096
<5>Kernel command line: console=ttyS0,115200 root=/dev/mmcblk0p2 rootwait loglevel=8 panic=10 console=ttyS0,115200 disp.screen0_output_mode=EDID:1920x1080p60 hdmi.audio=EDID:0 consoleblank=0 sunxi_no_mali_mem_reserve sunxi_g2d_mem_reserve=0 sunxi_ve_mem_reserve=0
<6>PID hash table entries: 4096 (order: 2, 16384 bytes)
<6>Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
<6>Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
<6>allocated 2097152 bytes of page_cgroup
<6>please try 'cgroup_disable=memory' option if you don't want memory cgroups
<6>Memory: 1024MB = 1024MB total
<5>Memory: 796068k/796068k available, 252508k reserved, 270336K highmem
<5>Virtual kernel memory layout:
vector  : 0xffff0000 - 0xffff1000   (   4 kB)
fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)
pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
modules : 0xbf000000 - 0xbfe00000   (  14 MB)
.text : 0xc0008000 - 0xc08c6e4c   (8956 kB)
.init : 0xc08c7000 - 0xc08fff80   ( 228 kB)
.data : 0xc0900000 - 0xc0973558   ( 462 kB)
.bss : 0xc097357c - 0xc0b47b58   (1874 kB)
<6>SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
<6>Preemptible hierarchical RCU implementation.
<6>    RCU dyntick-idle grace-period acceleration is enabled.
<6>    Additional per-CPU info printed with stalls.
<6>NR_IRQS:192
<6>Architected local timer running at 24.00MHz.
<6>sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
<2>start_kernel(): bug: interrupts were enabled early
<6>Console: colour dummy device 80x30
<6>Calibrating delay loop... <c>1915.28 BogoMIPS (lpj=9576448)
<6>pid_max: default: 32768 minimum: 301
<6>Mount-cache hash table entries: 512
<6>Initializing cgroup subsys cpuacct
<6>Initializing cgroup subsys memory
<6>Initializing cgroup subsys devices
<6>Initializing cgroup subsys freezer
<6>Initializing cgroup subsys blkio
<6>Initializing cgroup subsys perf_event
<6>CPU: Testing write buffer coherency: ok
<6>CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
<6>hw perfevents: enabled with ARMv7 Cortex-A7 PMU driver, 5 counters available
<6>Setting up static identity map for 0x40638ab0 - 0x40638b08
CPU1: Booted secondary processor
<6>CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
<6>Brought up 2 CPUs
<6>SMP: Total of 2 processors activated (3830.57 BogoMIPS).
<6>devtmpfs: initialized
<6>dummy:
<6>NET: Registered protocol family 16
<6>DMA: preallocated 256 KiB pool for atomic coherent allocations
<6>hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
<6>hw-breakpoint: maximum watchpoint size is 8 bytes.
<6>[ccu-inf] aw clock manager init
<6>[ccu-inf] aw_ccu_init
<6>[ccu-inf] script config pll3 to 297MHz
<6>[ccu-inf] script config pll4 to 960MHz
<6>[ccu-inf] script config pll6 to 600MHz
<6>[ccu-inf] script config pll7 to 297MHz
<6>[ccu-inf] script config pll8 to 336MHz
<6>Init eGon pin module V2.0
<6>bio: create slab <bio-0> at 0
<6>sunxi_gpio driver init ver 1.3
<6>gpiochip_add: registered GPIOs 1 to 2 on device: A1X_GPIO
<5>SCSI subsystem initialized
<7>libata version 3.00 loaded.
<6>usbcore: registered new interface driver usbfs
<6>usbcore: registered new interface driver hub
<6>usbcore: registered new device driver usb
<6>Linux media interface: v0.10
<6>Linux video capture interface: v2.00
<6>Advanced Linux Sound Architecture Driver Version 1.0.25.
<6>cfg80211: Calling CRDA to update world regulatory domain
<6>Switching to clocksource arch_sys_counter
<5>FS-Cache: Loaded
<6>CacheFiles: Loaded
[usb_manager]: CONFIG_USB_SW_SUNXI_USB0_OTG
[sw_hcd0]: usb host driver initialize........
[sw_hcd0]: open_usb_clock
[sw_hcd0]: host_init_state = 0
[sw_hcd0]: platform is usb host
[sw_hcd0]: sw_hcd_host0: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx (X), HB-ISO Tx (X), SoftConn)
[sw_hcd0]: sw_hcd_init_controller: sw_hcd_host0: USB Host mode controller at f1c13000 using PIO, IRQ 70
<6>sw_hcd_host0 sw_hcd_host0: sw_hcd host driver
<6>sw_hcd_host0 sw_hcd_host0: new USB bus registered, assigned bus number 1
<6>hub 1-0:1.0: USB hub found
<6>hub 1-0:1.0: 1 port detected
wrn: hcd is not enable, need not start hcd
[sw_hcd0]: sw_usb_host0_disable start
-------sw_hcd0_soft_disconnect---------
is_on = 0, hcd0_set_vbus_cnt = 0
[sw_hcd_host0]: Set USB Power Off
wrn: hcd is not enable, need not stop hcd
[sw_hcd0]: close_usb_clock
[sw_hcd0]: sw_usb_host0_disable end
[sw_udc]: udc_init: version 20080411
<6>NET: Registered protocol family 2
<6>IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
<6>TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
<6>TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
<6>TCP: Hash tables configured (established 131072 bind 65536)
<6>TCP: reno registered
<6>UDP hash table entries: 512 (order: 2, 16384 bytes)
<6>UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
<6>NET: Registered protocol family 1
<6>RPC: Registered named UNIX socket transport module.
<6>RPC: Registered udp transport module.
<6>RPC: Registered tcp transport module.
<6>RPC: Registered tcp NFSv4.1 backchannel transport module.
<3>dram para dram_rank_num fetch err
<3>aw_pm_init: fetch_and_save_dram_para err.
<6>audit: initializing netlink socket (disabled)
<5>type=2000 audit(0.620:1): initialized
highmem bounce pool size: 64 pages
<5>VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
<5>NFS: Registering the id_resolver key type
<6>NTFS driver 2.1.30 [Flags: R/W].
<6>fuse init (API version 7.18)
<6>SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled
<6>msgmni has been set to 1410
<3>alg: comp: Compression test 1 failed for lzo-generic: output len = 57
<6>alg: No test for stdrng (krng)
<6>Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
<6>io scheduler noop registered
<6>io scheduler deadline registered
<6>io scheduler cfq registered (default)
<6>sunxi disp driver loaded (/dev/disp api 1.0)
<6>Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled
<6>[uart]: used uart info.: 0x01
<6>[uart]: serial probe 0 irq 33 mapbase 0x01c28000
<6>sunxi-uart.0: ttyS0 at MMIO 0x1c28000 (irq = 33) is a U6_16550A
[    0.000000] Booting Linux on physical CPU 0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.4.91-sun7i+ (daniel@danand.de) (gcc version 4.8.2 (Ubuntu/Linaro 4.8.2-16ubuntu4) ) #1 SMP PREEMPT Wed May 28 13:07:28 CEST 2014
[    0.000000] CPU: ARMv7 Processor [410fc074] revision 4 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: sun7i
[    0.000000] Memory Reserved:
[    0.000000]     SYS  : 0x43000000 - 0x4300ffff  (  64 kB)
[    0.000000]     LCD  : 0x50000000 - 0x51ffffff  (  32 MB)
[    0.000000] cma: CMA: reserved 192 MiB at 43c00000
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] sunxi: Allwinner A20 (AW1651/sun7i) detected.
[    0.000000] On node 0 totalpages: 262144
[    0.000000] free_area_init_node: node 0, pgdat c096bc80, node_mem_map d2000000
[    0.000000]   DMA zone: 512 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 65024 pages, LIFO batch:15
[    0.000000]   Normal zone: 1008 pages used for memmap
[    0.000000]   Normal zone: 128016 pages, LIFO batch:31
[    0.000000]   HighMem zone: 528 pages used for memmap
[    0.000000]   HighMem zone: 67056 pages, LIFO batch:15
[    0.000000] PERCPU: Embedded 7 pages/cpu @d2808000 s8064 r8192 d12416 u32768
[    0.000000] pcpu-alloc: s8064 r8192 d12416 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 260096
[    0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mmcblk0p2 rootwait loglevel=8 panic=10 console=ttyS0,115200 disp.screen0_output_mode=EDID:1920x1080p60 hdmi.audio=EDID:0 consoleblank=0 sunxi_no_mali_mem_reserve sunxi_g2d_mem_reserve=0 sunxi_ve_mem_reserve=0
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] allocated 2097152 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] Memory: 1024MB = 1024MB total
[    0.000000] Memory: 796068k/796068k available, 252508k reserved, 270336K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc08c6e4c   (8956 kB)
[    0.000000]       .init : 0xc08c7000 - 0xc08fff80   ( 228 kB)
[    0.000000]       .data : 0xc0900000 - 0xc0973558   ( 462 kB)
[    0.000000]        .bss : 0xc097357c - 0xc0b47b58   (1874 kB)
[    0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]     RCU dyntick-idle grace-period acceleration is enabled.
[    0.000000]     Additional per-CPU info printed with stalls.
[    0.000000] NR_IRQS:192
[    0.000000] Architected local timer running at 24.00MHz.
[    0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
[    0.000000] start_kernel(): bug: interrupts were enabled early
[    0.000000] Console: colour dummy device 80x30
[    0.010870] Calibrating delay loop... 1915.28 BogoMIPS (lpj=9576448)
[    0.076020] pid_max: default: 32768 minimum: 301
[    0.079695] Mount-cache hash table entries: 512
[    0.083902] Initializing cgroup subsys cpuacct
[    0.087221] Initializing cgroup subsys memory
[    0.090644] Initializing cgroup subsys devices
[    0.094075] Initializing cgroup subsys freezer
[    0.097300] Initializing cgroup subsys blkio
[    0.100972] Initializing cgroup subsys perf_event
[    0.104549] CPU: Testing write buffer coherency: ok
[    0.109720] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.116815] hw perfevents: enabled with ARMv7 Cortex-A7 PMU driver, 5 counters available
[    0.122358] Setting up static identity map for 0x40638ab0 - 0x40638b08
[    0.238105] CPU1: Booted secondary processor
[    0.297227] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.299220] Brought up 2 CPUs
[    0.304529] SMP: Total of 2 processors activated (3830.57 BogoMIPS).
[    0.307636] devtmpfs: initialized
[    0.313081] dummy:
[    0.322380] NET: Registered protocol family 16
[    0.344585] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.352431] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.357225] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.360405] [ccu-inf] aw clock manager init
[    0.362676] [ccu-inf] aw_ccu_init
[    0.366764] [ccu-inf] script config pll3 to 297MHz
[    0.370513] [ccu-inf] script config pll4 to 960MHz
[    0.374280] [ccu-inf] script config pll6 to 600MHz
[    0.378029] [ccu-inf] script config pll7 to 297MHz
[    0.381774] [ccu-inf] script config pll8 to 336MHz
[    0.384531] Init eGon pin module V2.0
[    0.393364] bio: create slab <bio-0> at 0
[    0.396826] sunxi_gpio driver init ver 1.3
[    0.402422] gpiochip_add: registered GPIOs 1 to 2 on device: A1X_GPIO
[    0.405522] SCSI subsystem initialized
[    0.408398] libata version 3.00 loaded.
[    0.413031] usbcore: registered new interface driver usbfs
[    0.417352] usbcore: registered new interface driver hub
[    0.421511] usbcore: registered new device driver usb
[    0.424593] Linux media interface: v0.10
[    0.428196] Linux video capture interface: v2.00
[    0.433788] Advanced Linux Sound Architecture Driver Version 1.0.25.
[    0.439798] cfg80211: Calling CRDA to update world regulatory domain
[    0.444380] Switching to clocksource arch_sys_counter
[    0.446458] FS-Cache: Loaded
[    0.448641] CacheFiles: Loaded
[    0.459584] [usb_manager]: CONFIG_USB_SW_SUNXI_USB0_OTG
[    0.463524] [sw_hcd0]: usb host driver initialize........
[    0.467734] [sw_hcd0]: open_usb_clock
[    0.491936] [sw_hcd0]: host_init_state = 0
[    0.492906] [sw_hcd0]: platform is usb host
[    0.495824] [sw_hcd0]: sw_hcd_host0: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx (X), HB-ISO Tx (X), SoftConn)
[    0.507001] [sw_hcd0]: sw_hcd_init_controller: sw_hcd_host0: USB Host mode controller at f1c13000 using PIO, IRQ 70
[    0.519534] sw_hcd_host0 sw_hcd_host0: sw_hcd host driver
[    0.526233] sw_hcd_host0 sw_hcd_host0: new USB bus registered, assigned bus number 1
[    0.529629] hub 1-0:1.0: USB hub found
[    0.532523] hub 1-0:1.0: 1 port detected
[    0.536374] wrn: hcd is not enable, need not start hcd
[    0.537744] [sw_hcd0]: sw_usb_host0_disable start
[    0.543755] -------sw_hcd0_soft_disconnect---------
[    0.546734] is_on = 0, hcd0_set_vbus_cnt = 0
[    0.549784] [sw_hcd_host0]: Set USB Power Off
[    0.553529] wrn: hcd is not enable, need not stop hcd
[    0.554565] [sw_hcd0]: close_usb_clock
[    0.557040] [sw_hcd0]: sw_usb_host0_disable end
[    0.560212] [sw_udc]: udc_init: version 20080411
[    0.566514] NET: Registered protocol family 2
[    0.572868] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.579712] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.587173] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
[    0.593804] TCP: Hash tables configured (established 131072 bind 65536)
[    0.595992] TCP: reno registered
[    0.600879] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.606212] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.609824] NET: Registered protocol family 1
[    0.615102] RPC: Registered named UNIX socket transport module.
[    0.618795] RPC: Registered udp transport module.
[    0.622452] RPC: Registered tcp transport module.
[    0.627841] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.631667] dram para dram_rank_num fetch err
[    0.635674] aw_pm_init: fetch_and_save_dram_para err.
[    0.640767] audit: initializing netlink socket (disabled)
[    0.644459] type=2000 audit(0.620:1): initialized
[    0.648729] highmem bounce pool size: 64 pages
[    0.660118] VFS: Disk quotas dquot_6.5.2
[    0.665604] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.672405] NFS: Registering the id_resolver key type
[    0.676847] NTFS driver 2.1.30 [Flags: R/W].
[    0.680155] fuse init (API version 7.18)
[    0.688406] SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled
[    0.692538] msgmni has been set to 1410
[    0.703238] alg: comp: Compression test 1 failed for lzo-generic: output len = 57
[    0.706424] alg: No test for stdrng (krng)
[    0.713126] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    0.716012] io scheduler noop registered
[    0.719268] io scheduler deadline registered
[    0.722970] io scheduler cfq registered (default)
[    0.727801] sunxi disp driver loaded (/dev/disp api 1.0)
[    0.733371] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled
[    0.737997] [uart]: used uart info.: 0x01
[    0.742686] [uart]: serial probe 0 irq 33 mapbase 0x01c28000
[    0.768892] sunxi-uart.0: ttyS0 at MMIO 0x1c28000 (irq = 33) is a U6_16550A
<6>console [ttyS0] enabled
[    1.615483] console [ttyS0] enabled
<7>G2D: drv_g2d_init
[    1.621553] G2D: drv_g2d_init
<6>G2D: Module initialized.major:250
[    1.627887] G2D: Module initialized.major:250
<6>brd: module loaded
[    1.635204] brd: module loaded
<6>loop: module loaded
[    1.643991] loop: module loaded
[NAND] nand driver version: 0x2 0x9
[    1.650513] [NAND] nand driver version: 0x2 0x9
<4>Dev Sunxi softw311 nand magic does not match for MBR 1: softw411
[    1.714410] Dev Sunxi softw311 nand magic does not match for MBR 1: softw411
<4>Dev Sunxi softw311 nand magic does not match for MBR 2:
[    1.727475] Dev Sunxi softw311 nand magic does not match for MBR 2:
<4>Dev Sunxi softw311 nand magic does not match for MBR 3:
[    1.740527] Dev Sunxi softw311 nand magic does not match for MBR 3:
<4>Dev Sunxi softw311 nand magic does not match for MBR 4:
[    1.753572] Dev Sunxi softw311 nand magic does not match for MBR 4:
<4>Dev Sunxi softw311 nand header bad for all MBR copies, MBR corrupted or not present.
[    1.768346] Dev Sunxi softw311 nand header bad for all MBR copies, MBR corrupted or not present.
<4>Dev Sunxi softw411 nand: part 1, start 32768, size 131072
[    1.786803] Dev Sunxi softw411 nand: part 1, start 32768, size 131072
<4>Dev Sunxi softw411 nand: part 2, start 163840, size 7815168
[    1.798839] Dev Sunxi softw411 nand: part 2, start 163840, size 7815168
<6> nand: nand1 nand2
[    1.807476]  nand: nand1 nand2
[NAND]nand driver, ok.
[    1.813419] [NAND]nand driver, ok.
<6>sw_ahci sw_ahci.0: controller can't do PMP, turning off CAP_PMP
[    1.823175] sw_ahci sw_ahci.0: controller can't do PMP, turning off CAP_PMP
<4>sw_ahci sw_ahci.0: forcing PORTS_IMPL to 0x1
[    1.834427] sw_ahci sw_ahci.0: forcing PORTS_IMPL to 0x1
<6>sw_ahci sw_ahci.0: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode
[    1.847169] sw_ahci sw_ahci.0: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode
<6>sw_ahci sw_ahci.0: flags: ncq sntf pm led clo only pio slum part ccc
[    1.862057] sw_ahci sw_ahci.0: flags: ncq sntf pm led clo only pio slum part ccc
<6>scsi0 : sw_ahci_platform
[    1.873446] scsi0 : sw_ahci_platform
<6>ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 88
[    1.884222] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 88
<6>sunxi_emac Using mii phy on PortA
[    1.895715] sunxi_emac Using mii phy on PortA
<6>sunxi_emac Using MAC from SID: 02:01:05:01:31:7c[    1.914828] sunxi_emac Using MAC from SID: 02:01:05:01:31:7c<4>emac_init fetch emac using configuration failed

[    1.926744] emac_init fetch emac using configuration failed
<6>gmac driver is disabled
[    1.934960] gmac driver is disabled
<6>PPP generic driver version 2.4.2
[    1.941671] PPP generic driver version 2.4.2
<6>PPP BSD Compression module registered
[    1.949840] PPP BSD Compression module registered
<6>PPP Deflate Compression module registered
[    1.958561] PPP Deflate Compression module registered
<6>PPP MPPE Compression module registered
[    1.968603] PPP MPPE Compression module registered
<6>NET: Registered protocol family 24
[    1.976787] NET: Registered protocol family 24
<6>ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.987244] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
<6>ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.998992] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[sw-ehci1]: open clock
[    2.007600] [sw-ehci1]: open clock
[sw-ehci1]: Set USB Power ON
[    2.033643] [sw-ehci1]: Set USB Power ON
<6>sw-ehci sw-ehci.1: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.044008] sw-ehci sw-ehci.1: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
<6>sw-ehci sw-ehci.1: new USB bus registered, assigned bus number 2
[    2.057704] sw-ehci sw-ehci.1: new USB bus registered, assigned bus number 2
<6>sw-ehci sw-ehci.1: irq 71, io mem 0x01c14000
[    2.070387] sw-ehci sw-ehci.1: irq 71, io mem 0x01c14000
<6>sw-ehci sw-ehci.1: USB 2.0 started, EHCI 1.00
[    2.098799] sw-ehci sw-ehci.1: USB 2.0 started, EHCI 1.00
<6>hub 2-0:1.0: USB hub found
[    2.107630] hub 2-0:1.0: USB hub found
<6>hub 2-0:1.0: 1 port detected
[    2.114265] hub 2-0:1.0: 1 port detected
[sw-ohci1]: open clock
[    2.120809] [sw-ohci1]: open clock
<6>sw-ohci sw-ohci.1: SW USB2.0 'Open' Host Controller (OHCI) Driver
[    2.150302] sw-ohci sw-ohci.1: SW USB2.0 'Open' Host Controller (OHCI) Driver
<6>sw-ohci sw-ohci.1: new USB bus registered, assigned bus number 3
[    2.163678] sw-ohci sw-ohci.1: new USB bus registered, assigned bus number 3
<6>sw-ohci sw-ohci.1: irq 96, io mem 0x01c14400
[    2.175044] sw-ohci sw-ohci.1: irq 96, io mem 0x01c14400
<6>ata1: SATA link down (SStatus 0 SControl 300)
[    <2.238824] ata1: SATA link down (SStatus 0 SControl 300)
6>hub 3-0:1.0: USB hub found
[ <   2.246906] hub 3-0:1.0: USB hub found
6>hub 3-0:1.0: 1 port detected
[    2.2[53508] hub 3-0:1.0: 1 port detected
sw-ehci2]: open clock
[    2.259503] [sw-ehci2]: open clock
[sw-ehci2]: Set USB Power ON
[    2.282187] [sw-ehci2]: Set USB Power ON
<6>sw-ehci sw-ehci.2: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.292558] sw-ehci sw-ehci.2: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
<6>sw-ehci sw-ehci.2: new USB bus registered, assigned bus number 4
[    2.306264] sw-ehci sw-ehci.2: new USB bus registered, assigned bus number 4
<6>sw-ehci sw-ehci.2: irq 72, io mem 0x01c1c000
[    2.318867] sw-ehci sw-ehci.2: irq 72, io mem 0x01c1c000
<6>sw-ehci sw-ehci.2: USB 2.0 started, EHCI 1.00
[    2.338808] sw-ehci sw-ehci.2: USB 2.0 started, EHCI 1.00
<6>hub 4-0:1.0: USB hub found
[    2.347688] hub 4-0:1.0: USB hub found
<6>hub 4-0:1.0: 1 port detected
[    2.354322] hub 4-0:1.0: 1 port detected
[sw-ohci2]: open clock
[    2.360934] [sw-ohci2]: open clock
<6>sw-ohci sw-ohci.2: SW USB2.0 'Open' Host Controller (OHCI) Driver
[    2.390428] sw-ohci sw-ohci.2: SW USB2.0 'Open' Host Controller (OHCI) Driver
<6>sw-ohci sw-ohci.2: new USB bus registered, assigned bus number 5
[    2.403796] sw-ohci sw-ohci.2: new USB bus registered, assigned bus number 5
<6>sw-ohci sw-ohci.2: irq 97, io mem 0x01c1c400
[    2.415154] sw-ohci sw-ohci.2: irq 97, io mem 0x01c1c400
<6>hub 5-0:1.0: USB hub found
[    2.481849] hub 5-0:1.0: USB hub found
<6>hub 5-0:1.0: 1 port detected
[    2.488524] hub 5-0:1.0: 1 port detected
<6>Initializing USB Mass Storage driver...
[    2.496620] Initializing USB Mass Storage driver...
<6>usbcore: registered new interface driver usb-storage
[    2.506620] usbcore: registered new interface driver usb-storage
<6>USB Mass Storage support registered.
[    2.516201] USB Mass Storage support registered.
<6>usbcore: registered new interface driver ums-alauda
[    2.525737] usbcore: registered new interface driver ums-alauda
<6>usbcore: registered new interface driver ums-cypress
[    2.536676] usbcore: registered new interface driver ums-cypress
<6>usbcore: registered new interface driver ums-datafab
[    2.547689] usbcore: registered new interface driver ums-datafab
<6>usbcore: registered new interface driver ums_eneub6250
[    2.558865] usbcore: registered new interface driver ums_eneub6250
<6>usbcore: registered new interface driver ums-freecom
[    2.570041] usbcore: registered new interface driver ums-freecom
<6>usbcore: registered new interface driver ums-isd200
[    2.580952] usbcore: registered new interface driver ums-isd200
<6>usbcore: registered new interface driver ums-jumpshot
[    2.592015] usbcore: registered new interface driver ums-jumpshot
<6>usbcore: registered new interface driver ums-karma
[    2.602935] usbcore: registered new interface driver ums-karma
<6>usbcore: registered new interface driver ums-onetouch
[    2.613848] usbcore: registered new interface driver ums-onetouch
<6>usbcore: registered new interface driver ums-realtek
[    2.624949] usbcore: registered new interface driver ums-realtek
<6>usbcore: registered new interface driver ums-sddr09
[    2.635862] usbcore: registered new interface driver ums-sddr09
<6>usbcore: registered new interface driver ums-sddr55
[    2.646687] usbcore: registered new interface driver ums-sddr55
<6>usbcore: registered new interface driver ums-usbat
[    2.657439] usbcore: registered new interface driver ums-usbat
<6>mousedev: PS/2 mouse device common for all mice
[    2.667981] mousedev: PS/2 mouse device common for all mice
===========================hv_keypad_init=====================
[    2.679131] ===========================hv_keypad_init=====================
========HV Inital ===================
[    2.689408] ========HV Inital ===================
<3>tkey_fetch_sysconfig_para: tkey_unused.
[    2.698021] tkey_fetch_sysconfig_para: tkey_unused.
hv_keypad_init: after fetch_sysconfig_para:  normal_i2c: 0x0. normal_i2c[1]: 0x0
[    2.710197] hv_keypad_init: after fetch_sysconfig_para:  normal_i2c: 0x0. normal_i2c[1]: 0x0
<3>sunxi-rtc sunxi-rtc: Error: Set LOSC to external failed.
[    2.724337] sunxi-rtc sunxi-rtc: Error: Set LOSC to external failed.
<3>sunxi-rtc sunxi-rtc: Warning: RTC time will be wrong!
[    2.735742] sunxi-rtc sunxi-rtc: Warning: RTC time will be wrong!
<6>sunxi-rtc sunxi-rtc: rtc core: registered rtc as rtc0
[    2.747124] sunxi-rtc sunxi-rtc: rtc core: registered rtc as rtc0
<6>i2c /dev entries driver
[    2.755716] i2c /dev entries driver
config i2c gpio with gpio_config api
[    2.763019] config i2c gpio with gpio_config api
<6>axp_mfd 0-0034: AXP (CHIP ID: 0x41) detected
[    2.773345] axp_mfd 0-0034: AXP (CHIP ID: 0x41) detected
<6>axp_mfd 0-0034: AXP internal temperature monitoring enabled
[    2.784475] axp_mfd 0-0034: AXP internal temperature monitoring enabled
<4>i2c i2c-0: Invalid probe address 0x00
[    2.795692] i2c i2c-0: Invalid probe address 0x00
<6>I2C: i2c-0: AW16XX I2C adapter
[    2.803465] I2C: i2c-0: AW16XX I2C adapter
<4>i2c i2c-1: Invalid probe address 0x00
[    2.811587] i2c i2c-1: Invalid probe address 0x00
<6>I2C: i2c-1: AW16XX I2C adapter
[    2.819355] I2C: i2c-1: AW16XX I2C adapter
<4>i2c i2c-2: Invalid probe address 0x00
[    2.827421] i2c i2c-2: Invalid probe address 0x00
<6>I2C: i2c-2: AW16XX I2C adapter
[    2.835189] I2C: i2c-2: AW16XX I2C adapter
[cedar dev]: install start!!!
[    2.890582] [cedar dev]: install start!!!
[cedar dev]: install end!!!
[    2.897820] [cedar dev]: install end!!!
[tt]----- avs_dev driver load... ----
[    2.905048] [tt]----- avs_dev driver load... ----
[tt]-----      register iomem      ----
[    2.913357] [tt]-----      register iomem      ----
[tt]--- avs_dev driver load ok!! -----
[    2.921919] [tt]--- avs_dev driver load ok!! -----
[ace_drv] start!!!
[    2.928473] [ace_drv] start!!!
[ace_drv] init end!!!
[    2.933896] [ace_drv] init end!!!
[pa_drv] start!!!
[    2.938891] [pa_drv] start!!!
[pa_drv] init end!!!
[    2.944098] [pa_drv] init end!!!
<6>axp20_ldo1: 1300 mV
[    2.949723] axp20_ldo1: 1300 mV
<6>axp20_ldo2: 1800 <--> 3300 mV at 3000 mV
[    2.958160] axp20_ldo2: 1800 <--> 3300 mV at 3000 mV
<6>axp20_ldo3: 700 <--> 3500 mV at 2800 mV
[    2.968303] axp20_ldo3: 700 <--> 3500 mV at 2800 mV
<6>axp20_ldo4: 1250 <--> 3300 mV at 2800 mV
[    2.978640] axp20_ldo4: 1250 <--> 3300 mV at 2800 mV
<6>axp20_buck2: 700 <--> 2275 mV at 1400 mV
[    2.988838] axp20_buck2: 700 <--> 2275 mV at 1400 mV
<6>axp20_buck3: 700 <--> 3500 mV at 1250 mV
[    2.999284] axp20_buck3: 700 <--> 3500 mV at 1250 mV
<6>axp20_ldoio0: 1800 <--> 3300 mV at 2800 mV
[    3.009209] axp20_ldoio0: 1800 <--> 3300 mV at 2800 mV
<6>input: axp20-supplyer as /devices/platform/sunxi-i2c.0/i2c-0/0-0034/axp20-supplyer.28/input/input0
[    3.024020] input: axp20-supplyer as /devices/platform/sunxi-i2c.0/i2c-0/0-0034/axp20-supplyer.28/input/input0
<4>axp20_ldo2: Failed to create debugfs directory
[    3.052381] axp20_ldo2: Failed to create debugfs directory
<6>sunxi_wdt: sunxi WatchDog Timer Driver v1.0
[    3.062890] sunxi_wdt: sunxi WatchDog Timer Driver v1.0
<6>sunxi_wdt: initialized (timeout=23s, nowayout=0)
[    3.073107] sunxi_wdt: initialized (timeout=23s, nowayout=0)
<6>device-mapper: uevent: version 1.0.3
[    3.082876] device-mapper: uevent: version 1.0.3
<6>device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
[    3.095264] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
<6>device-mapper: multipath: version 1.3.0 loaded
[    3.108625] device-mapper: multipath: version 1.3.0 loaded
<6>device-mapper: multipath round-robin: version 1.0.0 loaded
[    3.119605] device-mapper: multipath round-robin: version 1.0.0 loaded
<6>device-mapper: multipath queue-length: version 0.1.0 loaded
[    3.131696] device-mapper: multipath queue-length: version 0.1.0 loaded
<6>device-mapper: multipath service-time: version 0.2.0 loaded
[    3.143869] device-mapper: multipath service-time: version 0.2.0 loaded
<6>cpuidle: using governor ladder
[    3.153879] cpuidle: using governor ladder
<6>cpuidle: using governor menu
[    3.160865] cpuidle: using governor menu
<6>[mmc-msg] sw_mci_init
[    3.167104] [mmc-msg] sw_mci_init
<6>[mmc-msg] MMC host used card: 0x1, boot card: 0x0, io_card 0
[    3.176123] [mmc-msg] MMC host used card: 0x1, boot card: 0x0, io_card 0
<6>[mmc-msg] sdc0 set round clock 400000, src 24000000
[    3.188533] [mmc-msg] sdc0 set round clock 400000, src 24000000
<6>[mmc-msg] sdc0 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    3.202793] [mmc-msg] sdc0 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B
<6>[mmc-msg] sdc0 Probe: base:0xf00ea000 irq:64 sg_cpu:c3c5f000(43c5f000) ret 0.
[    3.220045] [mmc-msg] sdc0 Probe: base:0xf00ea000 irq:64 sg_cpu:c3c5f000(43c5f000) ret 0.
[mmc_pm]: no sdio card used in configuration
[    3.232274] [mmc_pm]: no sdio card used in configuration
<6>sunxi_leds driver init
[    3.239945] sunxi_leds driver init
<7>Registered led device: green:ph20:led1
[    3.247489] Registered led device: green:ph20:led1
<7>Registered led device: blue:ph21:led2
[    3.256042] Registered led device: blue:ph21:led2
<7>Registered led device: boxred
[    3.263813] Registered led device: boxred
<7>Registered led device: boxgreen
[    3.271050] Registered led device: boxgreen
<6>ledtrig-cpu: registered to indicate activity on CPUs
[    3.280261] ledtrig-cpu: registered to indicate activity on CPUs
<6>usbcore: registered new interface driver usbhid
[    3.291466] usbcore: registered new interface driver usbhid
<6>usbhid: USB HID core driver
[    3.299842] usbhid: USB HID core driver
<6>ashmem: initialized
[    3.306393] ashmem: initialized
<6>logger: created 256K log 'log_main'
[    3.313193] logger: created 256K log 'log_main'
<6>logger: created 256K log 'log_events'
[    3.321506] logger: created 256K log 'log_events'
<6>logger: created 256K log 'log_radio'
[    3.329902] logger: created 256K log 'log_radio'
<6>logger: created 256K log 'log_system'
[    3.338309] logger: created 256K log 'log_system'
<6>IPv4 over IPv4 tunneling driver
[    3.349044] IPv4 over IPv4 tunneling driver
<6>TCP: bic registered
[    3.355924] TCP: bic registered
<6>TCP: cubic registered
[    3.361382] TCP: cubic registered
<6>TCP: westwood registered
[    3.367228] TCP: westwood registered
<6>TCP: highspeed registered
[    3.373407] TCP: highspeed registered
<6>TCP: hybla registered
[    3.379338] TCP: hybla registered
<6>TCP: htcp registered
[    3.384824] TCP: htcp registered
<6>TCP: vegas registered
[    3.390320] TCP: vegas registered
<6>TCP: veno registered
[    3.395806] TCP: veno registered
<6>TCP: scalable registered
[    3.401562] TCP: scalable registered
<6>TCP: lp registered
[    3.407145] TCP: lp registered
<6>TCP: yeah registered
[    3.412371] TCP: yeah registered
<6>TCP: illinois registered
[    3.418126] TCP: illinois registered
<6>Initializing XFRM netlink socket
[    3.424911] Initializing XFRM netlink socket
<6>NET: Registered protocol family 10
[    3.433157] NET: Registered protocol family 10
<6>NET: Registered protocol family 17
[    3.442054] NET: Registered protocol family 17
<6>NET: Registered protocol family 15
[    3.449964] NET: Registered protocol family 15
[mmc_pm]: No sdio card, please check your config !!
[    3.459067] [mmc_pm]: No sdio card, please check your config !!
<5>Registering the dns_resolver key type
[    3.468652] Registering the dns_resolver key type
<6>VFP support v0.3: [    3.475446] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 4
implementor 41 architecture 2 part 30 variant 7 rev 4
<5>Registering SWP/SWPB emulation handler
[    3.491686] Registering SWP/SWPB emulation handler
<4>axp20_buck2: Failed to create debugfs directory
[    3.501085] axp20_buck2: Failed to create debugfs directory
<6>[cpu_freq] INF:-------------------V-F Table-------------------
[    3.512795] [cpu_freq] INF:-------------------V-F Table-------------------
<6>[cpu_freq] INF:    voltage = 1450mv     frequency = 1008MHz
[    3.524720] [cpu_freq] INF:    voltage = 1450mv     frequency = 1008MHz
<6>[cpu_freq] INF:    voltage = 1400mv     frequency =  912MHz
[    3.535851] [cpu_freq] INF:    voltage = 1400mv     frequency =  912MHz
<6>[cpu_freq] INF:    voltage = 1300mv     frequency =  864MHz
[    3.546984] [cpu_freq] INF:    voltage = 1300mv     frequency =  864MHz
<6>[cpu_freq] INF:    voltage = 1200mv     frequency =  720MHz
[    3.558116] [cpu_freq] INF:    voltage = 1200mv     frequency =  720MHz
<6>[cpu_freq] INF:    voltage = 1100mv     frequency =  528MHz
[    3.569248] [cpu_freq] INF:    voltage = 1100mv     frequency =  528MHz
<6>[cpu_freq] INF:    voltage = 1050mv     frequency =  312MHz
[    3.580382] [cpu_freq] INF:    voltage = 1050mv     frequency =  312MHz
<6>[cpu_freq] INF:    voltage = 1050mv     frequency =  144MHz
[    3.591518] [cpu_freq] INF:    voltage = 1050mv     frequency =  144MHz
<6>[cpu_freq] INF:    voltage = 1000mv     frequency =    0MHz
[    3.602651] [cpu_freq] INF:    voltage = 1000mv     frequency =    0MHz
<6>[cpu_freq] INF:-----------------------------------------------
[    3.614561] [cpu_freq] INF:-----------------------------------------------
<6>[cpu_freq] INF:sunxi_cpufreq_initcall, get cpu frequency from sysconfig, max freq: 912MHz, min freq: 384MHz
[    3.631162] [cpu_freq] INF:sunxi_cpufreq_initcall, get cpu frequency from sysconfig, max freq: 912MHz, min freq: 384MHz
<6>registered taskstats version 1
[    3.645676] registered taskstats version 1
<6>I2C: i2c-3: HDMI I2C adapter
[    3.654361] I2C: i2c-3: HDMI I2C adapter
<6>[mmc-msg] mmc 0 detect change, present 1
[    4.203336] [mmc-msg] mmc 0 detect change, present 1
<6>[mmc-msg] sdc0 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    4.712357] [mmc-msg] sdc0 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timing LEGACY(SDR12) dt B
<6>[mmc-msg] sdc0 power on
[    4.723767] [mmc-msg] sdc0 power on
<6>[mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    4.752779] [mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
<6>[mmc-msg] sdc0 set round clock 400000, src 24000000
[    4.767075] [mmc-msg] sdc0 set round clock 400000, src 24000000
<3>[mmc-err] smc 0 err, cmd 52,  RTO
[    4.850082] [mmc-err] smc 0 err, cmd 52,  RTO
<3>[mmc-err] smc 0 err, cmd 52,  RTO
[    4.858582] [mmc-err] smc 0 err, cmd 52,  RTO
<6>[mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    4.871278] [mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
<6>[mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    4.891397] [mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
<3>[mmc-err] smc 0 err, cmd 5,  RTO
[    4.906173] [mmc-err] smc 0 err, cmd 5,  RTO
<3>[mmc-err] smc 0 err, cmd 5,  RTO
[    4.914495] [mmc-err] smc 0 err, cmd 5,  RTO
<3>[mmc-err] smc 0 err, cmd 5,  RTO
[    4.922816] [mmc-err] smc 0 err, cmd 5,  RTO
<3>[mmc-err] smc 0 err, cmd 5,  RTO
[    4.931133] [mmc-err] smc 0 err, cmd 5,  RTO
<6>[mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    4.944387] [mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
<6>[mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    4.962133] [mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
<6>[mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    4.982244] [mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
<6>[mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B
[    5.064895] [mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B
<6>[mmc-msg] sdc0 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B
[    5.082643] [mmc-msg] sdc0 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B
<6>[mmc-msg] sdc0 set round clock 46153846, src 600000000
[    5.097281] [mmc-msg] sdc0 set round clock 46153846, src 600000000
<6>[mmc-msg] sdc0 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B
[    5.162904] [mmc-msg] sdc0 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B
<6>mmc0: new high speed SDHC card at address aaaa
[    5.176842] mmc0: new high speed SDHC card at address aaaa
<6>mmcblk0: mmc0:aaaa SU32G 29.7 GiB
[    5.186253] mmcblk0: mmc0:aaaa SU32G 29.7 GiB
<6> mmcblk0: p1 p2 p3
[    5.194937]  mmcblk0: p1 p2 p3
<4>Timeout waiting for EDID info
[   13.687395] Timeout waiting for EDID info
<6>disp clks: lcd 148500000 pre_scale 1 hdmi 148500000 pll 297000000 2x 0
[   13.697934] disp clks: lcd 148500000 pre_scale 1 hdmi 148500000 pll 297000000 2x 0
<6>Console: switching to colour frame buffer device 240x67
[   14.857620] Console: switching to colour frame buffer device 240x67
<4>axp20_buck3: incomplete constraints, leaving on
[   14.902940] axp20_buck3: incomplete constraints, leaving on
<4>axp20_buck2: incomplete constraints, leaving on
[   14.913291] axp20_buck2: incomplete constraints, leaving on
<4>axp20_ldo4: incomplete constraints, leaving on
[   14.923543] axp20_ldo4: incomplete constraints, leaving on
<4>axp20_ldo3: incomplete constraints, leaving on
[   14.933708] axp20_ldo3: incomplete constraints, leaving on
<4>axp20_ldo2: incomplete constraints, leaving on
[   14.943877] axp20_ldo2: incomplete constraints, leaving on
<4>axp20_ldo1: incomplete constraints, leaving on
[   14.954037] axp20_ldo1: incomplete constraints, leaving on
<6>console [netcon0] enabled
[   14.962440] console [netcon0] enabled
<6>netconsole: network logging started
[   14.969603] netconsole: network logging started
<3>otg_wakelock_init: No USB transceiver found
[   14.978304] otg_wakelock_init: No USB transceiver found
<6>sunxi-rtc sunxi-rtc: setting system clock to 2010-01-01 00:00:00 UTC (1262304000)
[   14.991058] sunxi-rtc sunxi-rtc: setting system clock to 2010-01-01 00:00:00 UTC (1262304000)
<6>ALSA device list:
[   15.001629] ALSA device list:
<6>  #0: sunxi-CODEC  Audio Codec
[   15.012683]   #0: sunxi-CODEC  Audio Codec
<3>EXT3-fs (mmcblk0p2): error: couldn't mount because of unsupported optional features (240)
[   15.033352] EXT3-fs (mmcblk0p2): error: couldn't mount because of unsupported optional features (240)
<3>EXT2-fs (mmcblk0p2): error: couldn't mount because of unsupported optional features (240)
[   15.064612] EXT2-fs (mmcblk0p2): error: couldn't mount because of unsupported optional features (240)
<6>EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[   15.141914] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
<6>VFS: Mounted root (ext4 filesystem) on device 179:2.
[   15.155046] VFS: Mounted root (ext4 filesystem) on device 179:2.
<6>devtmpfs: mounted
[   15.165515] devtmpfs: mounted
<6>Freeing init memory: 224K
[   15.171412] Freeing init memory: 224K
Mount failed for selinuxfs on /sys/fs/selinux:  No such file or directory
<4>init: plymouth-upstart-bridge main process (72) terminated with status 1
[   15.660848] init: plymouth-upstart-bridge main process (72) terminated with status 1
<4>init: plymouth-upstart-bridge main process ended, respawning
[   15.676473] init: plymouth-upstart-bridge main process ended, respawning
<4>init: plymouth-upstart-bridge main process (82) terminated with status 1
[   15.752019] init: plymouth-upstart-bridge main process (82) terminated with status 1
<4>init: plymouth-upstart-bridge main process ended, respawning
[   15.765675] init: plymouth-upstart-bridge main process ended, respawning
<4>init: ureadahead main process (75) terminated with status 5
[   15.780826] init: ureadahead main process (75) terminated with status 5
<4>init: plymouth-upstart-bridge main process (86) terminated with status 1
[   15.849603] init: plymouth-upstart-bridge main process (86) terminated with status 1
<4>init: plymouth-upstart-bridge main process ended, respawning
[   15.863299] init: plymouth-upstart-bridge main process ended, respawning
<30>systemd-udevd[210]: starting version 204
<4>init: gator-daemon main process (224) terminated with status 1
UMP<2>: Inserting UMP device driver. Compiled: May 28 2014, time: 12:41:31
UMP<2>: Using OS memory backend, allocation limit: 134217728
UMP: UMP device driver  loaded
Mali: permit MALI_IOC_MEM_MAP_EXT ioctl for framebuffer (paddr=0x50000000, size=33554432)
<6>mali: use config clk_div 3
<6>mali: clk_div 3
Mali: mali clock set completed, clock is  320000000 Hz
<6>mali: use config clk_div 3
<6>mali: clk_div 3
Mali: mali clock set completed, clock is  320000000 Hz
Mali: Mali device driver loaded
* Stopping Send an event to indicate plymouth is up[ OK ]
* Starting Mount filesystems on boot[ OK ]
* Starting Signal sysvinit that the rootfs is mounted[ OK ]
* Starting Populate /dev filesystem[ OK ]
* Stopping Populate /dev filesystem[ OK ]
* Starting Fix-up /sys/kernel/debug filesystem[ OK ]
* Stopping Fix-up /sys/kernel/debug filesystem[ OK ]
* Starting Clean /tmp directory[ OK ]
* Starting Populate and link to /run filesystem[ OK ]
* Stopping Populate and link to /run filesystem[ OK ]
* Stopping Clean /tmp directory[ OK ]
* Stopping Track if upstart is running in a container[ OK ]
* Starting Initialize or finalize resolvconf[ OK ]
* Starting set console keymap[ OK ]
* Starting Signal sysvinit that virtual filesystems are mounted[ OK ]
* Starting Signal sysvinit that virtual filesystems are mounted[ OK ]
* Stopping set console keymap[ OK ]
* Starting Bridge udev events into upstart[ OK ]
* Starting Signal sysvinit that local filesystems are mounted[ OK ]
* Starting Signal sysvinit that remote filesystems are mounted[ OK ]
* Starting device node and kernel event manager[ OK ]
* Starting Load gator driver module and launch gator daemon[ OK ]
* Starting flush early job output to logs[ OK ]
* Starting Load gator driver module and launch gator daemon[fail]
* Stopping Mount filesystems on boot[ OK ]
* Starting load modules from /etc/modules[ OK ]
* Starting cold plug devices[ OK ]
* Starting log initial device creation[ OK ]
* Starting D-Bus system message bus[ OK ]
* Stopping flush early job output to logs[ OK ]
* Stopping load modules from /etc/modules[ OK ]
* Stopping cold plug devices[ OK ]
* Starting SystemD login management service[ OK ]
* Starting userspace bootsplash[ OK ]
* Stopping log initial device creation[ OK ]
* Stopping userspace bootsplash[ OK ]
* Starting Uncomplicated firewall[ OK ]
* Starting configure network device security[ OK ]
* Starting Send an event to indicate plymouth is up[ OK ]
* Starting system logging daemon[ OK ]
* Stopping Send an event to indicate plymouth is up[ OK ]
* Starting mDNS/DNS-SD daemon[ OK ]
* Starting Reload cups, upon starting avahi-daemon to make sure remote queues are populated[ OK ]
<4>init: avahi-cups-reload main process (400) terminated with status 1
* Starting Reload cups, upon starting avahi-daemon to make sure remote queues are populated[fail]
* Starting configure network device security[ OK ]
<6>sunxi_emac sunxi_emac.0: eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
* Starting configure network device[ OK ]
* Starting configure network device security[ OK ]
* Starting configure network device security[ OK ]
* Starting configure network device[ OK ]
* Starting configure network device[ OK ]
* Starting Mount network filesystems[ OK ]
* Starting Failsafe Boot Delay[ OK ]
* Stopping Mount network filesystems[ OK ]
* Starting Bridge socket events into upstart[ OK ]
* Starting Bridge file events into upstart[ OK ]
* Starting Mount network filesystems[ OK ]
<4>init: failsafe main process (441) killed by TERM signal
* Stopping Failsafe Boot Delay[ OK ]
* Starting System V initialisation compatibility[ OK ]
* Starting configure virtual network devices[ OK ]
* Setting up X socket directories...        [ OK ]
* Stopping Mount network filesystems[ OK ]

Last login: Fri Jan  1 01:00:12 CET 2010 on tty1
Welcome to Ubuntu 14.04 LTS (GNU/Linux 3.4.91-sun7i+ armv7l)

* Documentation:  https://help.ubuntu.com/
* Stopping System V initialisation compatibility[ OK ]
* Starting System V runlevel compatibility[ OK ]
* Starting regular background program processing daemon[ OK ]
* Starting save kernel messages[ OK ]
* Starting OpenSSH server[ OK ]
* Starting deferred execution scheduler[ OK ]
* Restoring resolver state...        * Starting CPU interrupts balancing daemon[ OK ]
* Stopping save kernel messages[ OK ]
[ OK ]
* Stopping System V runlevel compatibility[ OK ]
<4>init: plymouth-upstart-bridge main process ended, respawning
root@cubieboard:~# <4>init: tty1 main process (703) killed by TERM signal
<7>eth0: no IPv6 routers present

root@cubieboard:~# uname -a
Linux cubieboard 3.4.91-sun7i+ #1 SMP PREEMPT Wed May 28 13:07:28 CEST 2014 armv7l armv7l armv7l GNU/Linux
root@cubieboard:~#

One thought on “Stefanius Hybrid-Image + serial console + danand-3.4.91 kernel”

Leave a Reply

Your email address will not be published. Required fields are marked *

Protected with IP Blacklist CloudIP Blacklist Cloud